Grizzly G0513P Manuel d'utilisateur Page 69
- Page / 108
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
G0513 Series Bandsaws
-67-
8. When the wheels are coplanar, place a mark
on each wheel where you held the straight-
edge. This assures repeated accuracy every
time you adjust your wheels.
Note: When wheels are properly coplanar,
the blade may not be centered on the crown
of the wheel, but it will be balanced.
Adjusting Lower Wheel
Only do this procedure if you cannot make the
wheels coplanar with the tracking knob or by
shimming the upper wheel. Make sure the upper
wheel is adjusted as close as possible to being
coplanar with the lower wheel before beginning.
Do this procedure with the blade fully tensioned.
To adjust the lower wheel:
1. DISCONNECT BANDSAW FROM POWER!
2. Loosen the jam nuts on the lower wheel
adjustment hub (see Figure 100).
Figure 100. Lower wheel adjustment control.
Top Tilt
Side
Tilt
Bottom Tilt
Side
Tilt
Adjustment
Hub
3. Loosen one tilt adjustment set screw, then
tighten the opposing set screw approximately
an equal amount.
4. Check the wheels with the coplanarity gauge,
then adjust the lower wheel at the hub as
needed until it is parallel and coplanar with
the top wheel.
5. Tighten the jam nuts to lock the tilt adjust-
ment set screws in position.
The space between the magnetic motor brake
and brake shoe is preset by the factory at 0.008"
(0.2mm). To compensate for this wear, you should
adjust this space every two to three years, or if
the brake takes over five seconds for to stop the
motor.
Tools Needed
Phillips Head Screwdriver .................................. 1
Feeler Gauge 0.008" ......................................... 2
Dollar Bill, Folded Once (Optional) .................... 1
Hex Wrench 3mm .............................................. 1
Hex Wrench 4mm .............................................. 1
To adjust the magnetic brake:
1. DISCONNECT BANDSAW FROM POWER!
2. Remove the motor fan cover, then loosen the
cap screws securing the motor fan and brake
shoe (see Figure 101).
Magnetic Brake
Adjustment
(G0513X2B,
G0513X2BF)
3. Place the feeler gauge (or dollar bill folded
once) between the brake shoe and magnetic
brake on either side.
4. Tighten the cap screws on the brake shoe
and motor fan, remove the feeler gauge, then
reinstall the motor fan cover.
Figure 101. Adjusting distance between
magnetic brake and brake shoe.
Magnetic
Brake
Cap
Screw
Motor
Fan
Brake
Shoe
Optional
Dollar Bill
OFF
ON
- MODEL G0513 SERIES 1
- HEAVY-DUTY 17" BANDSAW 1
- Table of Contents 3
- INTRODUCTION 5
- Basic Controls 6
- Rear Controls 7
- SECTION 1: SAFETY 10
- SECTION 2: POWER SUPPLY 13
- Grounding Requirements 14
- Circuit Requirements 14
- Extension Cords 16
- Voltage Conversion 16
- SECTION 3: SETUP 17
- Inventory 18
- G0513X2F 19
- Site Considerations 20
- Moving & Placing 21
- Mounting 22
- Assembly 22
- G0513X2BF) 25
- Installing Resaw 26
- Fence (G0513X2 26
- G0513X2B 26
- G0513X2BF, & 26
- G0513X2F) 26
- Initial Blade Tracking 27
- Adjusting Positive 28
- Dust Collection 29
- Power Cord 29
- Connection 29
- (G0513X2BF & 29
- Test Run 30
- OFF Button 31
- Tensioning Blade 32
- 4 of a 32
- Deflection Method 33
- Adjusting Blade 34
- Support Bearings 34
- G0513P, & G0513ANV) 36
- 4") blade 38
- Aligning Fence 39
- Calibrating Miter 40
- SECTION 4: OPERATIONS 41
- Straight Cuts 42
- Irregular Cuts 42
- Basic Cutting Tips 42
- Operation Overview 43
- Workpiece 43
- Inspection 43
- Table Tilt 44
- Guide Post 45
- Fine Tune Tracking 45
- Blade Selection 46
- Tooth Set 47
- Tooth Type 47
- Blade Care 49
- Blade Break-In 49
- Blade Changes 50
- Crosscutting 52
- Resawing 52
- Stacked Cuts 54
- SECTION 5: ACCESSORIES 55
- Recommended Metal Protectants 56
- Basic Eye Protection 56
- SECTION 6: MAINTENANCE 57
- Tension Adjustment Assembly 58
- Trunnions 58
- SECTION 7: SERVICE 59
- Checking V-Belt 62
- Replacing V-Belt 62
- 4" 63
- Blade Lead 63
- 2" blade 64
- Adjusting Guide 65
- Post Travel 65
- Checking Coplanarity 67
- Shimming Upper Wheel 68
- Adjusting Lower Wheel 69
- SECTION 8: WIRING 70
- Rewired to 110V 71
- 6-15 PLUG 72
- G0513X2BF Wiring Diagram 73
- G0513X2F 220V Wiring Diagram 74
- G0513X2F 110V Wiring Diagram 75
- SECTION 9: PARTS 76
- Lower Blade Guides 78
- G0513/G0513P/G0513ANV Fence 79
- Guides & Miter Gauge 80
- G0513 Labels 82
- G0513P Labels 83
- G0513ANV Labels 84
- G0513X2 Main 85
- G0513X2 Main Parts List 86
- G0513X2 Labels 87
- G0513X2B Main 88
- G0513X2B Main Parts List 89
- G0513X2B Labels 91
- G0513X2BF Main 92
- G0513X2BF Main Parts List 93
- G0513X2BF Labels 95
- G0513X2F Main 96
- G0513X2F Main Parts List 97
- G0513X2F Labels 99
- G0513 Series Bandsaws 100
- WARRANTY CARD 105
- FOLD ALONG DOTTED LINE 106
- WARRANTY & RETURNS 107
- 24 HOURS A DAY! 108
- 1-800-523-4777 108
Produits connexes et manuels pour Scies à moteur Grizzly G0513P
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.205 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels