Grizzly G0513P Manuel d'utilisateur Page 67
- Page / 108
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
G0513 Series Bandsaws
-65-
Aligning Wheels
Components and Hardware Needed: Qty
56" Long 2x4 ..................................................... 1
Tools Needed:
Hex Wrenches 4 & 6 mm .............................1 Ea
Wrench 13mm ................................................... 1
Tape Measure .................................................... 1
Coplanarity Gauge (see Figure 96) .................. 1
Straightedge ........................................................
Fine Ruler .......................................................... 1
Wheel alignment is one of the most critical factors
for optimal performance from your bandsaw.
Heat, vibration, wandering, blade wear, tire wear
and overall bandsaw wear are considerably
decreased when the wheels are properly aligned
or “coplanar.”
Coplanar wheels automatically track the blade
by balancing it on the crown of the wheel. This is
known as coplanar tracking.
Checking Coplanarity
1. Make the "Coplanarity Gauge" shown in
Figure 96.
Note: For best results, straighten the 2x4
with a jointer before cutting.
2. DISCONNECT BANDSAW FROM POWER!
3. Remove the fence and open both wheel cov-
ers.
4. Adjust the blade guides away from the blade,
loosen blade tension, remove the table insert
and pin, then remove the blade.
5. Remove the table.
6. Reinstall the blade, making sure the guide
bearings and support bearings are away from
the blade, then tighten your blade to the ten-
sion that it will be used during operation.
7. Place your coplanarity gauge up against both
wheels in the positions shown in Figure 97.
Coplanarity
Gauge
Gauge Positions
Tracking
Knob
Adjustment
Hub
Wheels
Figure 97. Checking for coplanarity.
Figure 96. Dimensions of coplanarity gauge.
Side View
56"
3-
1
⁄2"
17"
17"
22"
1-
1
⁄2"
- MODEL G0513 SERIES 1
- HEAVY-DUTY 17" BANDSAW 1
- Table of Contents 3
- INTRODUCTION 5
- Basic Controls 6
- Rear Controls 7
- SECTION 1: SAFETY 10
- SECTION 2: POWER SUPPLY 13
- Grounding Requirements 14
- Circuit Requirements 14
- Extension Cords 16
- Voltage Conversion 16
- SECTION 3: SETUP 17
- Inventory 18
- G0513X2F 19
- Site Considerations 20
- Moving & Placing 21
- Mounting 22
- Assembly 22
- G0513X2BF) 25
- Installing Resaw 26
- Fence (G0513X2 26
- G0513X2B 26
- G0513X2BF, & 26
- G0513X2F) 26
- Initial Blade Tracking 27
- Adjusting Positive 28
- Dust Collection 29
- Power Cord 29
- Connection 29
- (G0513X2BF & 29
- Test Run 30
- OFF Button 31
- Tensioning Blade 32
- 4 of a 32
- Deflection Method 33
- Adjusting Blade 34
- Support Bearings 34
- G0513P, & G0513ANV) 36
- 4") blade 38
- Aligning Fence 39
- Calibrating Miter 40
- SECTION 4: OPERATIONS 41
- Straight Cuts 42
- Irregular Cuts 42
- Basic Cutting Tips 42
- Operation Overview 43
- Workpiece 43
- Inspection 43
- Table Tilt 44
- Guide Post 45
- Fine Tune Tracking 45
- Blade Selection 46
- Tooth Set 47
- Tooth Type 47
- Blade Care 49
- Blade Break-In 49
- Blade Changes 50
- Crosscutting 52
- Resawing 52
- Stacked Cuts 54
- SECTION 5: ACCESSORIES 55
- Recommended Metal Protectants 56
- Basic Eye Protection 56
- SECTION 6: MAINTENANCE 57
- Tension Adjustment Assembly 58
- Trunnions 58
- SECTION 7: SERVICE 59
- Checking V-Belt 62
- Replacing V-Belt 62
- 4" 63
- Blade Lead 63
- 2" blade 64
- Adjusting Guide 65
- Post Travel 65
- Checking Coplanarity 67
- Shimming Upper Wheel 68
- Adjusting Lower Wheel 69
- SECTION 8: WIRING 70
- Rewired to 110V 71
- 6-15 PLUG 72
- G0513X2BF Wiring Diagram 73
- G0513X2F 220V Wiring Diagram 74
- G0513X2F 110V Wiring Diagram 75
- SECTION 9: PARTS 76
- Lower Blade Guides 78
- G0513/G0513P/G0513ANV Fence 79
- Guides & Miter Gauge 80
- G0513 Labels 82
- G0513P Labels 83
- G0513ANV Labels 84
- G0513X2 Main 85
- G0513X2 Main Parts List 86
- G0513X2 Labels 87
- G0513X2B Main 88
- G0513X2B Main Parts List 89
- G0513X2B Labels 91
- G0513X2BF Main 92
- G0513X2BF Main Parts List 93
- G0513X2BF Labels 95
- G0513X2F Main 96
- G0513X2F Main Parts List 97
- G0513X2F Labels 99
- G0513 Series Bandsaws 100
- WARRANTY CARD 105
- FOLD ALONG DOTTED LINE 106
- WARRANTY & RETURNS 107
- 24 HOURS A DAY! 108
- 1-800-523-4777 108
Produits connexes et manuels pour Scies à moteur Grizzly G0513P
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.083 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels