Grizzly G0513P Manuel d'utilisateur Page 18
- Page / 108
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
-16-
G0513 Series Bandsaws
Inventory
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
G0513, G0513P, & G0513ANV
Shipping Inventory (Figures 7 & 8): Qty
A. Bandsaw (not shown) ................................. 1
B. Table ........................................................... 1
C. Miter Gauge ................................................ 1
D. Rear Rail .................................................... 1
E. Front Rail ................................................... 1
F. Fence Assembly ......................................... 1
G. Guide Post Handwheel............................... 1
Hardware & Tools (Not Shown) Qty
• Eye Bolt M10-1.5 (May Be Installed) .......... 1
• Flat Washers 8mm (Table) ......................... 4
• Lock Washers 8mm (Table) ....................... 4
• Hex Bolts M8-1.25 x 16 (Table) .................. 4
• Hex Bolt M8-1.25 x 90 (Positive Stop) ........ 1
• Hex Nuts M8-1.25 (Positive Stop, Fence)... 2
• Cap Screws M6-1 x 16 (Fence) .................. 2
• Hex Bolts M6-1 x 20 (Fence) ...................... 2
• Lock Washers 6mm (Fence) ...................... 2
• Flat Washers 6mm (Fence) ........................ 2
• Hex Nut M6-1 (Fence) ................................ 1
• Table Pin..................................................... 1
• Table Insert ................................................. 1
• Fence Handle M8-1.25 x 22 (Fence) .......... 1
• Rail Pad M6-1 x 18 (Fence) ........................ 1
• Hex Wrench 5mm, 8mm....................1 Each
• Open End Wrench 10 x 13mm ................... 1
Figure 8. Other bandsaw components.
D
E
F
G
Figure 7. Table and miter gauge.
C
B
NOTICE
If you cannot find an item on this list, care-
fully check the machine and the packaging
materials. Some of these items may be pre-
installed for shipping or become misplaced
during unpacking.
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
- MODEL G0513 SERIES 1
- HEAVY-DUTY 17" BANDSAW 1
- Table of Contents 3
- INTRODUCTION 5
- Basic Controls 6
- Rear Controls 7
- SECTION 1: SAFETY 10
- SECTION 2: POWER SUPPLY 13
- Grounding Requirements 14
- Circuit Requirements 14
- Extension Cords 16
- Voltage Conversion 16
- SECTION 3: SETUP 17
- Inventory 18
- G0513X2F 19
- Site Considerations 20
- Moving & Placing 21
- Mounting 22
- Assembly 22
- G0513X2BF) 25
- Installing Resaw 26
- Fence (G0513X2 26
- G0513X2B 26
- G0513X2BF, & 26
- G0513X2F) 26
- Initial Blade Tracking 27
- Adjusting Positive 28
- Dust Collection 29
- Power Cord 29
- Connection 29
- (G0513X2BF & 29
- Test Run 30
- OFF Button 31
- Tensioning Blade 32
- 4 of a 32
- Deflection Method 33
- Adjusting Blade 34
- Support Bearings 34
- G0513P, & G0513ANV) 36
- 4") blade 38
- Aligning Fence 39
- Calibrating Miter 40
- SECTION 4: OPERATIONS 41
- Straight Cuts 42
- Irregular Cuts 42
- Basic Cutting Tips 42
- Operation Overview 43
- Workpiece 43
- Inspection 43
- Table Tilt 44
- Guide Post 45
- Fine Tune Tracking 45
- Blade Selection 46
- Tooth Set 47
- Tooth Type 47
- Blade Care 49
- Blade Break-In 49
- Blade Changes 50
- Crosscutting 52
- Resawing 52
- Stacked Cuts 54
- SECTION 5: ACCESSORIES 55
- Recommended Metal Protectants 56
- Basic Eye Protection 56
- SECTION 6: MAINTENANCE 57
- Tension Adjustment Assembly 58
- Trunnions 58
- SECTION 7: SERVICE 59
- Checking V-Belt 62
- Replacing V-Belt 62
- 4" 63
- Blade Lead 63
- 2" blade 64
- Adjusting Guide 65
- Post Travel 65
- Checking Coplanarity 67
- Shimming Upper Wheel 68
- Adjusting Lower Wheel 69
- SECTION 8: WIRING 70
- Rewired to 110V 71
- 6-15 PLUG 72
- G0513X2BF Wiring Diagram 73
- G0513X2F 220V Wiring Diagram 74
- G0513X2F 110V Wiring Diagram 75
- SECTION 9: PARTS 76
- Lower Blade Guides 78
- G0513/G0513P/G0513ANV Fence 79
- Guides & Miter Gauge 80
- G0513 Labels 82
- G0513P Labels 83
- G0513ANV Labels 84
- G0513X2 Main 85
- G0513X2 Main Parts List 86
- G0513X2 Labels 87
- G0513X2B Main 88
- G0513X2B Main Parts List 89
- G0513X2B Labels 91
- G0513X2BF Main 92
- G0513X2BF Main Parts List 93
- G0513X2BF Labels 95
- G0513X2F Main 96
- G0513X2F Main Parts List 97
- G0513X2F Labels 99
- G0513 Series Bandsaws 100
- WARRANTY CARD 105
- FOLD ALONG DOTTED LINE 106
- WARRANTY & RETURNS 107
- 24 HOURS A DAY! 108
- 1-800-523-4777 108
Produits connexes et manuels pour Scies à moteur Grizzly G0513P
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.974 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels