Grizzly G0513P Manuel d'utilisateur Page 49
- Page / 108
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
G0513 Series Bandsaws
-47-
Blade Breakage
Many conditions may cause a bandsaw blade to
break. Blade breakage is unavoidable in some
cases, since it is the natural result of the peculiar
stresses that bandsaw blades must endure.
Blade breakage is also due to avoidable circum-
stances. Avoidable blade breakage is most often
the result of poor care or judgement on the part
of the operator when mounting or adjusting the
blade or support guides.
The most common causes of blade breakage
are:
• Faulty alignment or adjustment of the blade
guides.
• Forcing or twisting a wide blade around a
short radius.
• Feeding the workpiece too fast.
• Dull or damaged teeth.
• Over-tensioned blade.
• Top blade guide assembly set too high above
the workpiece. Adjust the top blade guide
assembly so that there is approximately
1
⁄8"–
1
⁄4" between the bottom of the assembly
and the workpiece.
• Using a blade with a lumpy or improperly fin-
ished braze or weld.
• Continuously running the bandsaw when not
in use.
• Leaving the blade tensioned when not in
use.
• Using the wrong pitch (TPI) for the workpiece
thickness. The general rule of thumb is to
have not less than two teeth in contact with
the workpiece at all times during cutting.
Blade Care &
Break-In
Blade Care
A bandsaw blade is a thin piece of steel that is
subjected to tremendous strain. You can obtain
longer use from a bandsaw blade if you give it fair
treatment and always use the appropriate feed
rate for your operation.
Be sure to select blades with the proper width,
set, type, and pitch for each application. Using the
wrong blade will produce unnecessary heat and
shorten the life of the blade.
A clean blade will perform much better than a dirty
blade. Dirty or gummed up blades pass through
the cutting material with much more resistance
than clean blades. This extra resistance also
causes unnecessary heat.
Blade Break-In
The sharp teeth tips and edges of a new blade are
extremely sharp, and cutting at too fast of a feed
rate fractures the beveled edges of the teeth and
causes premature blade wear.
To properly break-in a new blade:
1. Choose the correct speed for the blade and
material of the operation.
2. Reduce the feed pressure by half for the first
50–100 in
2
of material cut.
3. To avoid twisting the blade when cutting,
adjust the feed pressure when the total width
of the blade is in the cut.
- MODEL G0513 SERIES 1
- HEAVY-DUTY 17" BANDSAW 1
- Table of Contents 3
- INTRODUCTION 5
- Basic Controls 6
- Rear Controls 7
- SECTION 1: SAFETY 10
- SECTION 2: POWER SUPPLY 13
- Grounding Requirements 14
- Circuit Requirements 14
- Extension Cords 16
- Voltage Conversion 16
- SECTION 3: SETUP 17
- Inventory 18
- G0513X2F 19
- Site Considerations 20
- Moving & Placing 21
- Mounting 22
- Assembly 22
- G0513X2BF) 25
- Installing Resaw 26
- Fence (G0513X2 26
- G0513X2B 26
- G0513X2BF, & 26
- G0513X2F) 26
- Initial Blade Tracking 27
- Adjusting Positive 28
- Dust Collection 29
- Power Cord 29
- Connection 29
- (G0513X2BF & 29
- Test Run 30
- OFF Button 31
- Tensioning Blade 32
- 4 of a 32
- Deflection Method 33
- Adjusting Blade 34
- Support Bearings 34
- G0513P, & G0513ANV) 36
- 4") blade 38
- Aligning Fence 39
- Calibrating Miter 40
- SECTION 4: OPERATIONS 41
- Straight Cuts 42
- Irregular Cuts 42
- Basic Cutting Tips 42
- Operation Overview 43
- Workpiece 43
- Inspection 43
- Table Tilt 44
- Guide Post 45
- Fine Tune Tracking 45
- Blade Selection 46
- Tooth Set 47
- Tooth Type 47
- Blade Care 49
- Blade Break-In 49
- Blade Changes 50
- Crosscutting 52
- Resawing 52
- Stacked Cuts 54
- SECTION 5: ACCESSORIES 55
- Recommended Metal Protectants 56
- Basic Eye Protection 56
- SECTION 6: MAINTENANCE 57
- Tension Adjustment Assembly 58
- Trunnions 58
- SECTION 7: SERVICE 59
- Checking V-Belt 62
- Replacing V-Belt 62
- 4" 63
- Blade Lead 63
- 2" blade 64
- Adjusting Guide 65
- Post Travel 65
- Checking Coplanarity 67
- Shimming Upper Wheel 68
- Adjusting Lower Wheel 69
- SECTION 8: WIRING 70
- Rewired to 110V 71
- 6-15 PLUG 72
- G0513X2BF Wiring Diagram 73
- G0513X2F 220V Wiring Diagram 74
- G0513X2F 110V Wiring Diagram 75
- SECTION 9: PARTS 76
- Lower Blade Guides 78
- G0513/G0513P/G0513ANV Fence 79
- Guides & Miter Gauge 80
- G0513 Labels 82
- G0513P Labels 83
- G0513ANV Labels 84
- G0513X2 Main 85
- G0513X2 Main Parts List 86
- G0513X2 Labels 87
- G0513X2B Main 88
- G0513X2B Main Parts List 89
- G0513X2B Labels 91
- G0513X2BF Main 92
- G0513X2BF Main Parts List 93
- G0513X2BF Labels 95
- G0513X2F Main 96
- G0513X2F Main Parts List 97
- G0513X2F Labels 99
- G0513 Series Bandsaws 100
- WARRANTY CARD 105
- FOLD ALONG DOTTED LINE 106
- WARRANTY & RETURNS 107
- 24 HOURS A DAY! 108
- 1-800-523-4777 108
Produits connexes et manuels pour Scies à moteur Grizzly G0513P
(96 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.494 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels