Grizzly G1023 Manuel d'utilisateur

10" HEAVY-DUTY TABLE SAWMODEL G1023INSTRUCTION MANUALCOPYRIGHT © 1990 BY GRIZZLY IMPORTS, INC REG #TX 3 170 579WARNING: NO PORTION OF THIS MANUAL

G1023 Heavy-Duty Table Saw -9-Figure 3.SwitchThe magnetic switch comes prewired to themotor. However, you must mount the switch tothe table saw body b

Figure 5.-10- G1023 Heavy-Duty Table Saw8. If the wing tilts down, remove the wing andstick layers of masking tape under each boltnear the bottom edge

G1023 Heavy-Duty Table Saw -11-Figure 7.BladeThe Model G1023 is not supplied with a blade.For a selection of blades, including dado sets,refer to the

Figure 11.-12- G1023 Heavy-Duty Table Saw4. Recheck guard alignment to the blade and tothe table top. Adjust as necessary and tight-en down all the bo

G1023 Heavy-Duty Table Saw -13-Figure 13.Table InsertsYour table saw comes with two table inserts. Oneis for standard blades and the other is for dado

-14- G1023 Heavy-Duty Table SawFigure 15.Figure 14.1. Install the table insert by putting your fingersinto the finger holes of the insert and liftingt

G1023 Heavy-Duty Table Saw -15-Figure 18.Figure 16.Figure 17.Table Mount Holes5. The difference between distance A and dis-tance B must be equal to or

-16- G1023 Heavy-Duty Table SawFigure 21.90° Stop BoltJam NutFrontTrunnionGearedTrunnion5. Loosen the jam nut and thread the stop boltin or out not mo

G1023 Heavy-Duty Table Saw -17-Figure 23.5. Loosen the jam nut behind the 45° stop bolt.Tighten or loosen the stop bolt to adjust thestopping position

-18- G1023 Heavy-Duty Table SawFigure 24.Angle PointerAngle PointerOnce the positive stops have been set, the anglepointer will require adjusting. To

G1023 Heavy-Duty Table Saw -1-Table Of ContentsPAGE1. SAFETY INSTRUCTIONS ...

G1023 Heavy-Duty Table Saw -19-Figure 26.Figure 27.FenceThe fence must engage and square up on thefront rail before the rear clamp engages the backrai

-20- G1023 Heavy-Duty Table SawFigure 29.5. Loosen the locking lever until it is approxi-mately two-thirds engaged. Tighten the rearadjusting screw un

G1023 Heavy-Duty Table Saw -21-Pre-Run CheckBefore you begin to use your model G1023 TableSaw, you should give it a thorough inspection.While making y

-22- G1023 Heavy-Duty Table Saw3. Combination Blade: Used for cutting withand across the grain. A compromisebetween a rip blade and a cross-cut blade,

G1023 Heavy-Duty Table Saw -23-Figure 34.4. Plywood Blade: Used for cutting plywood orveneers. A Plywood blade will have 80+teeth, a steep alternate t

-24- G1023 Heavy-Duty Table SawRippingRipping means to cut with the grain of the wood.In other materials such as MDF or plywood, rip-ping simply means

G1023 Heavy-Duty Table Saw -25-SECTION 6: MAINTENANCEV-BeltTo ensure optimum power transmission from themotor to the blade, the V-belts must be in goo

-26- G1023 Heavy-Duty Table SawFigure 39.The shielded ball bearings in the motor andthroughout most of the model G1023 require nofurther lubrication d

G1023 Heavy-Duty Table Saw -27-The following pages contain general machinedata, troubleshooting guide, parts diagram, partslist and Warranty/Return in

-28- G1023 Heavy-Duty Table Saw1989945678910111213163031181920212527323337B403841434544474855057525423555358606162636465666869707172737475767778798182

-2- G1023 Heavy-Duty Table Saw1. Wear eye protection.2. Use saw-blade guard and spreader for everyoperation for which it can be used, includingall thr

G1023 Heavy-Duty Table Saw -29-001 P1023001 CABINET002 P1023002 SCALE003 P1023003 SELF TAPPING SCREW004 P1023004 TRAP DOOR005 PN02 HEX NUT 5⁄16"

-30- G1023 Heavy-Duty Table Saw411404409407405406408403402410409401413412401 P1023401 KNOB402 P1023402 FLAT WASHER 1⁄4"403 P1023403 MITER GAUGE B

G1023 Heavy-Duty Table Saw -31-512513509511511507507502504505506508501503510501 P1022174 GUARD502 P1022171 HEX BOLT M6-1.0X40MM503 PLN03M LOCK NUT M6-

17191863403833303132341352935162313924252512872039282326232423101115143727542524

G1023 Heavy-Duty Table Saw -33-601 P1022Z064 FENCE602 PFH08M FLT HD SCREW 603 PW01M FLAT WASHER 8MM 604 PS05M PHLP HD SCREW M5-0.8 X 8605 P1022Z037

-34- G1023 Heavy-Duty Table SawMACHINE DATAGRIZZLY MODEL G1023 TABLE SAWDesign Type...

G1023 Heavy-Duty Table Saw -35-SYMPTOMMotor will not start.Motor will not start; fuses orcircuit breakers blow.Motor overheats.Motor stalls (resulting

-36- G1023 Heavy-Duty Table SawGrizzly Imports, Inc. warrants every product it sells for a period of 1 year to the original purchaser from thedate of

G1023 Heavy-Duty Table Saw -3-Additional Safety Instructions For Table Saws1. ALWAYS use guard, splitter and anti-kick-back fingers on all '&apos

-4- G1023 Heavy-Duty Table SawGrizzly Imports, Inc. is proud to offer the ModelG1023 10" Heavy-Duty Table Saw. This modelG1023 is a part of Grizz

G1023 Heavy-Duty Table Saw -5-UnpackingThe Model G1023 is shipped from the manufac-turer in a carefully packed carton. If you discoverthe machine is d

-6- G1023 Heavy-Duty Table SawClean upThe table and other unpainted parts of the ModelG1023 are coated with a waxy oil that protectsthem from corrosio

G1023 Heavy-Duty Table Saw -7-Circuit RequirementsThe Model G1023 Table Saw has one 3 HPmotor. It has been pre-wired to operate at 220V,single phase o

-8- G1023 Heavy-Duty Table SawBeginning AssemblyMost of your Model G1023 Table Saw has beenassembled at the factory, but some parts must beassembled o